Appliance Energy Cost Calculator

One kilowatt-hour is 1,000 watts for one hour — about 18.2¢ at the U.S. average. A 1,000 W appliance running two hours a day costs roughly $0.36 a day, or $11 a month.

W

Average draw while running

h

Effective full-power hours

Sets the price per kWh

Estimated cost

$11.07/ month

$0.36 per day

$132.86 per year

Per hour
$0.18
kWh / month
61
Rate used
18.2¢
vs U.S. average
—

Estimate only. Appliance at 1000 W for 2 h/day, priced at your state’s average residential rate. Your utility and plan may differ — see methodology.

How the calculation works

Electricity is sold in kilowatt-hours. One kilowatt-hour is 1,000 watts used for one hour. To price any appliance you need three numbers: how many watts it draws, how many hours a day it runs, and what you pay per kWh.

The wattage is printed on the appliance label or in the manual, but the label usually shows the maximum the unit can pull, not what it draws on average. A microwave rated 1,200 W only uses that while it is actually heating. A refrigerator rated 800 W cycles on and off and averages closer to 100–150 W. That is why this calculator asks for average watts and effective hours, not nameplate ratings.

Typical wattage for common appliances

ApplianceTypical drawTypical use
Space heater1,500 W4 h/day in heating season
Central AC (3-ton)3,500 W6 h/day in cooling season
Window AC1,000 W8 h/day
Refrigerator150 W average24 h/day
Electric water heater4,000 W3 h/day
Electric dryer3,000 W1 h/day
Pool pump1,500 W6 h/day
EV Level 2 charger7,200 W1.2 h/day (35 mi commute)
Average draw while running — confirm against your own label.

Find the rate you actually pay

Your bill has two parts worth separating: the supply charge (per kWh) and the delivery or fixed charges (per day or per month). The calculator uses the all-in per-kWh figure, which is what you get by dividing the total bill by total kWh used. If you have a time-of-use plan, run the numbers twice — once at the off-peak rate and once at the on-peak rate — because the gap between them is often two to three times.

Default rates here come from EIA residential averages by state. They are a reasonable starting point, but a single utility can sit well above or below its state average, so treat the result as an estimate until you plug in your own number.

Where the money usually goes

  • Heating and cooling are typically the two largest lines in a U.S. home — often close to half of annual electricity use.
  • Water heating is usually next, and it runs year-round, which is why it shows up on summer bills too.
  • Anything that creates heat — dryers, ovens, space heaters, hot tubs — is a large load by design. Efficiency gains there come from using it less, not from a smarter plug.
  • Devices that run 24 hours a day (refrigerators, network gear, pool pumps) add up slowly but never stop.

Which of the three inputs is most likely wrong

The rate is the most reliable input: state averages are published monthly and rarely move more than a few percent. Hours are the least reliable, because people estimate their own habits badly — a "two hour" space heater is often four. Wattage sits in between: the label is exact for devices that run at a fixed load, and wildly misleading for anything with a compressor.

That is why the useful exercise is not chasing the perfect wattage, but bracketing the hours. Run the calculator with half the hours you think you use and with double. If the difference does not change your decision, the estimate is good enough. If it does, a $20 plug-in meter will settle it in a week.

Frequently asked questions

How do I convert watts to kWh?

Divide watts by 1,000 to get kilowatts, then multiply by hours. A 1,500 W heater running 4 hours uses 1.5 × 4 = 6 kWh.

Why is my calculated cost lower than my bill?

Because one appliance is rarely the whole bill. Fixed monthly charges, delivery fees, taxes and every other device in the house are outside this estimate. Compare the appliance total against your total kWh, not against the dollar amount due.

Should I use the wattage on the label?

Only as an upper bound. Labels show maximum draw. For cycling appliances like refrigerators, freezers and dehumidifiers, average draw is far lower. Use a plug-in energy monitor for a week if you want the real number.

Does a higher wattage always mean a higher bill?

No. A 1,500 W heater used one hour costs less than a 150 W refrigerator running all day. Energy is watts multiplied by time, so duration matters as much as power.

Which state has the highest electricity rates?

Hawaii is consistently the most expensive, followed by states in the Northeast and California. Rates in the South Central states and the Northwest are usually the lowest. Switch the state selector to see the effect instantly.

Does this include taxes and fixed charges?

No. It prices the energy only, at your state’s average per-kWh rate. Fixed customer charges and taxes are separate lines on the bill.

Why do two identical appliances cost different amounts?

Age, insulation, placement and how full they are. Two identical refrigerators can differ by 30% if one sits in a hot garage.

Keep going

The cost of one appliance rarely tells the whole story. These are the calculators people open next.